Engine rebuild kit for the Honda Gold Wing GL1100 from 1980-1981. Time to rebuild? If you're diving in and doing the top end, replacing engine cover gaskets and replacing seals this is a great kit to have on hand!
Gasket Set Includes
12251-MG9-306 - Cylinder Head Gasket - x2
12328-371-000 - Valve Cover Gasket - x2
11831-371-010 - Right Front Cover Gasket - x1
11832-371-010 - Left Front Cover Gasket - x1
30376-371-306 - Breaker Gasket - x2
12391-371-306 - Cover Gasket - x1
19429-371-306 - Water Joint Gasket - x2
11372-463-306 - Final Gear Cover Gasket - x1
11391-371-306 - Transmission Cover Gasket - x1
11393-463-306 - Clutch Cover Gasket - x1
11394-371-306 - Right Crankcase Gasket - x1
11396-371-306 - Water Pump Gasket - x1
15128-371-000 - Oil Passage Gasket - x1
15229-371-000 - Clutch Oil Pump Gasket - x1
30379-463-306 - Pulser Cover Gasket - x1
18291-286-306 - Exhaust Gasket - x4
12209-MB9-003 - Valve Stem Seal - x8
91303-371-000 - Oil Strainer Gasket - x1
91301-371-005 - O-Ring 40X2.6 - x4
91307-MB0-003 - O-Ring 54X2 - x1
91301-MB6-003 - O-Ring 21.9X2.3 - x4
91305-371-003 - O-Ring 6.5X1.5 - x2
91307-PH7-660 - O-Ring 13.5X1.4 - x1
91308-371-003 - O-Ring 4.1X1.5 - x2
91307-PH9-000 - O-Ring 15.5X1.4 - x1
91259-333-000 - O-Ring 9.5X1.7 - x1
91302-001-020 - O-Ring 30.8x3.2 - x2
91304-HB3-003 - O-Ring 33.5X3.0 - x1
91302-377-000 - O-Ring 15X2.5 - x1
91305-426-003 - O-Ring 46X2 - x1
91305-422-000 - O-Ring 9.8X2.4 - x1
91312-371-013 - O-Ring 23X2.1 - x2
91316-425-003 - O-Ring 89X4.5 - x1
91318-500-000 - O-Ring 27X2.7 - x1
91319-300-000 - O-Ring 13X2.5 - x1
91303-634-010 - O-Ring 12.5X2.2 - x1
91307-703-000 - O-Ring 25.4X2.4 - x1
91306-371-013 - O-Ring 17.7X2.7 - x1
91309-283-005 - O-Ring 42.5X2 - x1
Oil Seal Kit Includes:
Clutch Cover Seal
Crankshaft Seal
Cylinder Head Seal - Quantity 2
Cylinder Block Seal
Tachometer Seal
Oil Pump Seal 1
Oil Pump Seal 2
Rear Case - Small Seal
Rear Case - Large Seal
Installation Tips:
Press your seals in straight with a seal driver or a socket with a slightly smaller OD than the seal. Both surfaces must be free of dirt to create an oil tight seal.
All sealing surfaces for gaskets must be clean and flat to make a proper seal, sometimes non-hardening sealant is necessary.
Fits Honda:
GL1100 Gold Wing - 1980-1981
GL11000I Gold Wing Interstate - 1980-1981
