2 Pack tapered oval performance pod filter in chrome. Fits many late 70's and early 80's Honda's as well as other models, see dimensions below. This filter is also available in all black.
Features
- Flexible rubber molded flange instead of the 2 piece design like many pod filters.
- Flange design has no step so it does not block important openings on the carburetor intake.
- Tighter, more streamline fit without any risk of vibration causing the air filter to move independently while attached to the carburetors.
Keep in mind, for the bike to run smoothly, you may need to install larger jets and make other adjustments to match the higher air flow. The rubber mounts are flexible and can be mounted on 53mm and 55mm carburetor flanges.
IMPORTANT: Be sure to measure your carburetor prior to purchase. Also measure how much room you have between the carburetor and the frame or any side covers. Use the dimensions below to see if these will work on your bike. Just because the filters fit the carbs doesn't mean they'll fit in the bike without some obstruction. Some carburetors have very tight spacing which will not allow for a 73mm wide pod filter to fit side by side.
Dimensions:
54mm ID where it mounts to the carburetors
70mm Air filter length
86mm Total length including rubber
73mm Width of oval
104mm Height of oval
Fits Honda:
CB400A Hawk Hondamatic - 1978
CB400TI Hawk I - 1978-1979
CB400TII Hawk II - 1978-1979
CB400T Hawk - 1980-1981
CM400A Hondamatic - 1979-1981
CM400C Custom - 1981
CM400E - 1980-1981
CM400T - 1979-1981
CB450T Hawk - 1982
CB450SC Nighthawk - 1982-1986
CM450A Hondamatic - 1982-1983
CM450C Custom - 1982
CM450E - 1982-1983
CX500 - 1978-1979
CX500C Custom - 1979-1982
CX500D Deluxe - 1979-1981
GL500 Silver Wing - 1981-1982
GL500I Silver Wing Interstate - 1981-1982
CX650C Custom - 1983
GL650 Silver Wing - 1983
GL650I Silver Wing Interstate - 1983
Fits Kawasaki:
KZ1000A/J - 1981-1983
KZ1000B/K LTD - 1981-1982
KZ1000C/P Police - 1982-1999
KZ1000M CSR - 1981-1982
KZ1000R Lawson Replica - 1982-1983
KZ1100A - 1981-1983
KZ1100B GPZ - 1981-1982
KZ1100D Spectre - 1982-1983
KZ1100L LTD Shaft - 1983
KZ1300 - 1981-1982
KZ750B/E - 1980-1982
KZ750H LTD - 1980-1983
KZ750L - 1983
KZ750N Spectre - 1982-1983
ZL1000 Eliminator - 1987
ZN1100B LTD - 1984-1985
ZX550 GPZ - 1984-1985
ZX750 GPZ - 1982-1985
Fits Suzuki:
GS1000G - 1980-1981
GS1000GL - 1980-1981
GS1000S - 1980
GS1000S Katana - 1982
GS1100E - 1980-1983
GS1100G - 1982-1983
GS1100GK - 1982-1983
GS1100L - 1980
GS1100S Katana - 1983
GS1150E - 1984-1986
GS700E - 1985
GS750E - 1980-1983
GS750ES - 1983
GS850G - 1979-1983
GS850GL - 1980-1983
Fits Yamaha:
SR500 - 1978-1981
XJ650 Maxim - 1980-1983
XJ650L Turbo Seca - 1981-1983
XJ650R Seca - 1982
XJ900 Seca - 1983
XS1100 - 1978-1981
XS1100L Mid-Special - 1980-1981
XS1100S Special - 1979-1981
XS750 - 1977-1979
XS750S - 1978-1979
XS850 - 1980-1981
XS850L Mid-Special - 1980-1981
XS850S Special - 1980-1981
XT500 - 1976-1981
NOTE: Fits other model bikes as well. Check your carburetor flange diameter before purchase.
1 Review Hide Reviews Show Reviews
-
Good pod filters
I'm happy with these filters. They are larger than the cone shaped pod filters I was replacing, but there is no problem with fitment, and they look good. I'm happy with the higher quality too. My last one were the black cone ones from 4into1. This is on a cm400e. The only issues are minor, but they would look better if they came with black bands instead of silver (I reused the black bands I already had), and the color is more marron than red. Minor issues though, and I'm glad I got them.
