Reproduction front brake (stop light) switch / clutch switch, this plugs into the clutch perch on models with disc brakes and it plugs into the brake lever perch on models with drum front brakes. It is either used as a brake switch if you have drum brakes, or as a clutch safety switch if you have a model with disc brakes up front.
Overall Length: 26 1/2"
2 Male Bullet Connectors - 1 black wire / 1 green/yellow wire
Replaces Honda part numbers: 35340-329-003, 35360-341-000
Fits Honda:
NC50 Express - 1977-1979
CT90 Trail 90 - 1976-1979
XL100 - 1976
XL100K1 - 1975
XL100S - 1979-1980
CT110 Trail 110 - 1980-1986
CB125S - 1976, 1978
MT125 Elsinore - 1976
MT125K0 Elsinore - 1974
MT125K1 Elsinore - 1975
XL125S - 1979-1980
XL175 - 1976-1978
XL175K0 - 1973
XL175K1 - 1974
XL175K2 - 1975
CM185T Twinstar - 1978-1979
XL185S - 1979-1980
CB200T - 1976
CM200T Twinstar - 1980
MT250 Elsinore - 1976
MT250 Elsinore (MT250K0) - 1974
MT250K1 Elsinore - 1975
XL250 Motosport 250 (XL250K0) - 1972-1973
XL250K1 - 1974
XL250K2 - 1975
XL250S - 1978-1981
XL350 (XL350K0) - 1974
XL350K1 - 1975
CB360T - 1976
CB360T (CB360T0) - 1975
CJ360T - 1976-1977
CL360 Scrambler 360 (CL360K0) - 1974
CL360K1 Scrambler 360 - 1975
CB400F Super Sport 400 Four - 1976-1977
CB400F Super Sport 400 Four (CB400F0) - 1975
CB500T 500 Twin DOHC - 1976
CB500T 500 Twin DOHC (CB500T0) - 1975
XL500S - 1979-1981
CB550F Super Sport 550 Four - 1976-1977
CB550F Super Sport 550 Four (CB550F0) - 1975
CB550K 550 Four - 1976-1978
CB550K 550 Four (CB550K0) - 1974
CB550K1 550 Four - 1975
CB750F 750 Super Sport - 1976-1978
CB750F 750 Super Sport (CB750F0) - 1975
CB750K 750 Four - 1976-1978
CB750K3 750 Four - 1973
CB750K4 750 Four - 1974
CB750K5 750 Four - 1975
GL1000 Gold Wing - 1976-1977
GL1000 Gold Wing (GL1000K0) - 1975
GL1000LTD Gold Wing Limited Edition - 1976
5 Reviews Hide Reviews Show Reviews
-
Clutch Switch
Slid right in the slot and works as advertised.
-
Switch
Great fit , works well to prevent starting in gear . Very much a safety item .
-
Front Brake Switch
I ran into a issue with the switch sitting too deep in the perch I ordered for the brake lever to depress the switch. I filled the perch recess with glue to raise the level of the switch so it would make contact with the lever. A little surprising since the switch, perch and lever were all reproductions for the same model bike.
-
Brake Switch
Works great plugged right into the stock harness!
-
Perfect Fit
Ordered for my 1977 CJ360T...a perfect replacement for the OEM switch, and an easy job to install.